- Home
- Archives
- 2025
- Vol. 6 Issue 2
- Article
Design and Analysis of Deep Drawing Die for Copper Cup
Authors
1PG Scholar, Department of Mechanical Engineering, Jaihind College of Engineering, Kuran, Maharashtra, India. 2Guide, Department of Mechanical Engineering, Jaihind College of Engineering, Kuran, Maharashtra, India. 34Professor, CO Guide, Department of Mechanical Engineering, Jaihind College of Engineering, Kuran, Maharashtra, India.
Article Information
- DOI
- No DOI
- Published In
- Volume 6, Issue 2 (2025)
- Published Online
- March-April 2025
- Pages
- 158-160
- Article Type
- Original Article
- Check for updates
- No DOI available for cross-reference
References
1. Liwen Tian, Changfeng Men, Qiang Yu, “Optimization of Process Parameters in Deep Drawing Process Based on Orthogonal
Experiment Method”, 3rd International Conference on Mechanical Engineering and Intelligent Systems (ICMEIS 2015), pp. 684-688.
2. Pradeep M Patil and Prof. Prashant S Bajaj, I. Constantin, “Tool Design of Cylindrical Cup for Multi-Stage Drawing Process”,
International Journal of Latest Trends in Engineering and Technology (IJLTET), ISSN: 2278- 621X, 2013, pp. 100-106.
3. S V. Modanloo, R. Hasanzadeh*, P. Esmaili, “The Study of Deep Drawing of Brass-steel Laminated Sheet Composite Using Taguchi
Method”, IJE TRANSACTIONS A: Basics, Vol. 29, No. 1, (January 2016), pp. 684-688.
4. B. Beglarzadeh, B. Davoodi, “Numerical simulation and experimental examination of forming defects in multi-point deep drawing
process”, ISSN 1392- 1207. MECHANIKA. 2016 VOLUME 22(3): PP: 182-189.
5. Dr R Uday Kumar, P Ravinder Reddy and A V SitaRamaraju “Determination of blank holding pressure in hydroforming deep drawing
process”, InternationalJournal of mechanical Engineering and robotics research (2012): ISSN 2278 – 01492.
6. Daw-Kwei Leu. “Prediction of the maximum drawing load in the cup drawing process of sheet metals”, Journal of Materials
Processing Technology, ElsevierScience S.A. 1997; 72; 256- 261.
7. Kenichi Hanazaki “Significant change in mechanical properties of deep drawn ultrafine grained copper wire by additional
deformation”, Materials Science and Engineering a 534 (2012) 720– 723.
8. D. K .Karupannasamy “A friction model for loading and reloading effects in deep drawing processes” Wear318 (2014)27–39.
9. Gow-Yi T, Ming-Nan H. “Analytical modified model of the cold bond rolling of unbounded double-layers sheet considering hybrid
friction”. J Mater Process Technol 2003; 140:441–6.
10. Danesh Manesh H, Karimi Taheri A. “Theoretical and experimental investigation of cold rolling of tri-layer strip”. J Mater Process
Technol 2005; 166:163–72.
11. Islam MD, Olabi AG, Hashmi MSJ. “Feasibility of multi-layered tubular components forming by hydroforming and finite element
simulation”. J Mater Process Technol 2006; 174:394–8.
12. Lang L, Danckert J, Nielsen KB. “Multi-layer sheet hydroforming: experimental and numerical investigation into the very thin layer
in the middle”. J Mater Process Technol 2005; 170:524– 35
Experiment Method”, 3rd International Conference on Mechanical Engineering and Intelligent Systems (ICMEIS 2015), pp. 684-688.
2. Pradeep M Patil and Prof. Prashant S Bajaj, I. Constantin, “Tool Design of Cylindrical Cup for Multi-Stage Drawing Process”,
International Journal of Latest Trends in Engineering and Technology (IJLTET), ISSN: 2278- 621X, 2013, pp. 100-106.
3. S V. Modanloo, R. Hasanzadeh*, P. Esmaili, “The Study of Deep Drawing of Brass-steel Laminated Sheet Composite Using Taguchi
Method”, IJE TRANSACTIONS A: Basics, Vol. 29, No. 1, (January 2016), pp. 684-688.
4. B. Beglarzadeh, B. Davoodi, “Numerical simulation and experimental examination of forming defects in multi-point deep drawing
process”, ISSN 1392- 1207. MECHANIKA. 2016 VOLUME 22(3): PP: 182-189.
5. Dr R Uday Kumar, P Ravinder Reddy and A V SitaRamaraju “Determination of blank holding pressure in hydroforming deep drawing
process”, InternationalJournal of mechanical Engineering and robotics research (2012): ISSN 2278 – 01492.
6. Daw-Kwei Leu. “Prediction of the maximum drawing load in the cup drawing process of sheet metals”, Journal of Materials
Processing Technology, ElsevierScience S.A. 1997; 72; 256- 261.
7. Kenichi Hanazaki “Significant change in mechanical properties of deep drawn ultrafine grained copper wire by additional
deformation”, Materials Science and Engineering a 534 (2012) 720– 723.
8. D. K .Karupannasamy “A friction model for loading and reloading effects in deep drawing processes” Wear318 (2014)27–39.
9. Gow-Yi T, Ming-Nan H. “Analytical modified model of the cold bond rolling of unbounded double-layers sheet considering hybrid
friction”. J Mater Process Technol 2003; 140:441–6.
10. Danesh Manesh H, Karimi Taheri A. “Theoretical and experimental investigation of cold rolling of tri-layer strip”. J Mater Process
Technol 2005; 166:163–72.
11. Islam MD, Olabi AG, Hashmi MSJ. “Feasibility of multi-layered tubular components forming by hydroforming and finite element
simulation”. J Mater Process Technol 2006; 174:394–8.
12. Lang L, Danckert J, Nielsen KB. “Multi-layer sheet hydroforming: experimental and numerical investigation into the very thin layer
in the middle”. J Mater Process Technol 2005; 170:524– 35
Related Articles
Share Article
*Instagram doesn't support direct link sharing from web. Copy the link and share it in your Instagram story or post.